Canadian Dollars
Guaranteed Fitment
Always the correct part
have questions?
Always the correct part
We know our products
Fast & Reliable
Availability: 2 to 3 Weeks
Fluke Networks LIQ-KIT-IS60 OffersSolve connectivity problems with this Cable and Network tester, the testing solution for verifying cable performance up to 10 gigabytes per second. Moreover, this network tester validates cable performance using frequency-based measurements and a wire map of the cable under test. Completely eliminating the need for another device, this tester performs ping tests to verify connectivity and nearest switch diagnostics to identify key network issues and validate switch configurations.
Features
Active network diagnostics
Diagnostic protocols: Link Layer Discovery Protocol (LLDP), Cisco Discovery Protocol (CDP), Fast Link Pulses (FLP), Internet Control Messaging Protocol (ICMP), Dynamic Host Configuration Protocol (DHCP)
IP address setup: LinkIQ address, DNS server, gateway for IPv4 or v6 either manually or via DHCP
IP ping test results: Four response time results for target, DNS server(s), gateway, plus average and number lost
Nearest device diagnostics (if available through diagnostic protocols): Switch name / IP + MAC address, port number, VLAN name, advertised data rates, advertised duplex
Power over ethernet compatibility: Ethernet alliance certified to IEEE 802.3af/at/bt, hardware negotiation with signature resistance, software negotiation with LLDP/CDP
Power over ethernet diagnostics: Advertised power class (0 to 8), advertised available power, powered pairs, diagnostics for both single and dual signatures
Power over ethernet measurements: Loaded voltage (V), loaded power (W)
Port blink: Blink the light of the connected port
Cable testing you trust
Capable of measuring lengths up to 1000' (305 m) and providing distance to faults including opens, shorts, and unterminated cables, the LinkIQ™ uses the remote ID to acquire a complete wire map of the cable pairs, which helps identify miswired and split pairs.
The primary cable testing feature of the LinkIQ™ is the cable performance test, which qualifies the cabling bandwidth from 10BASE-T to 10GBASE-T (10 Mb/s up to 10 Gb/s). It performs these tests via frequency-based measurements.
Using IEEE standards-based measurements ensures tested links meet performance requirements, unlike transmission testers, which only provide that specific test devices can communicate over the link.
Operators may set performance requirements from 10 Mb/s ti 10 Gb/s for a simple pass/fail indication.
Network testing you need
Along with the robust cable testing features, the LinkIQ™ also provides detailed information on the nearest connected switch and connectivity testing with IP ping. The LinkIQ™ negotiates with the switch to identify the advertised data rate (up to 10GBASE-T), half/full duplex identification, the switch name and IP address, the port number, and the VLAN information.
The ping test verifies connectivity to devices on the local network or the internet and supports IPv4 and v6. The LinkIQ's address may be set up manually or through DHCP. Once set up, the ping test is run as part of the autotest when a switch is detected. Results of the ping test include the identification and response time of four pings to the target, the DNS server, and gateway.
In-depth PoE testing
While power over Ethernet makes installation devices such as security cameras and access points simpler, a survey by the Ethernet Alliance of over 800 installers, integrators, and end users found that four of five respondents experienced difficulties in integrating PoE systems. Part of this can be traced to the fact that IEEE offers three PoE standards, the term "PoE" is not registered, and there are a variety of non-standards-compliant implementations as well.
To simplify PoE installation and troubleshooting, the LinkIQ™ displays the pairs where power is provided, including the different power levels and pairs for dual-signature implementations. Further, the LinkIQ™ will place a load on the connection to ensure the advertised power is actually being delivered by the switch across the cabling infrastructure. The LinkIQ™ has been certified by the Ethernet Alliance to IEEE-802.3™ standards for reliable multivendor interoperability.
LinkWare™ documentation
The LinkIQ™ provides complete documentation abilities for the tests it performs. Up to 1000 results with descriptive names can be stored and recalled in the tester. Test names and numbers automatically increment as each is saved ("annex B-1", "annex B-2", "annex B-3", etc.), saving lots of time when testing cables in sequence.
Report data may be exported to a PC for documentation purposes. The LinkIQ uses LinkWare™ PC, Fluke Networks' reporting software, which supports a variety of testers going back 20 years and is the industry's de-facto reporting solution with tens of thousands of active users. LinkWare can be used to store the results and generate PDF reports.
Applications
| Cable Test Specifications | |
| Test Port | Shielded 8-pin modular jack accepts 8-pin modular (RJ45) plugs |
| Commissioning Autotest | 10GBASE-T, 5GBASE-T, 2.5GBASE-T, 1000BASE-T, 100BASE-TX, 10BASE-T, wire map onlyTest Speed: 6 seconds for lengths <230' (70 m) |
| Cable Types | Balanced twisted-pair cablingUnshielded twisted-pairScreened twisted-pair2-pair and/or 4-pair |
| Wire Map-Only Tests | Document wire mapLength of each pairDiagnose split pairsUser selectable T568A or T568BUser selectable crossover settings (straight through, half-crossover, full-crossover)Test speed: 1 second for lengths <394' (120 m) |
| Length (Maximum) | 1000' (305 m) |
| Nominal Velocity of Propagation (NVP) | User settable |
| Tone Generator | Generates digital tones compatible with Fluke Networks IntelliTone probeGenerates analog tones compatible with general analog probes |
| Remote ID Locators | Use remote ID terminations to identify up to 7 unique ports or office outlets |
| General Specifications | |
| Vibration | Random, 2 g, 5 Hz to 500 Hz |
| Drop | 1 m drop, 6 sides |
| Power Adapter | Input: 100 to 240 V AC ±10%, 50/60 HzOutput: 15 V DC, 2 A maximumA class II |
| Host Interface | USB-C |
| Display | 800 x 480 color capacitive multi-touch |
| Environmental Conditions | Operating temperature: 32 to 113°F (0 to 45°C)Storage Temperature: -14 to 140°F (-10 to 60°C)Operating relative humidity: 0 to 90% from 32 to 95°F (0 to 35°C), 0 to 70% from 95 to 113°F (35 to 45°F)Operating altitude: 13,123' (4000 m), 10,499' (3200 m) with ac adapter |
| Battery | Type: Lithium-ion, 3.6 V, 6400 mAhLife: 8 hours typicalCharge time: 4.5 hoursCharging temperature range: 32 to 104°F (0 to 40°C) |
| Supported Languages | English, German, French, Japanese, Spanish, Thai, Traditional Chinese, Simplified Chinese, Korean, Russian, Italian, Portugese |
| Dimensions | 8.5 x 4.5" (21.6 x 11.4 cm) |
| Weight | 1.38 lbs (624 g) |
All returns must be authorized. Items returned prior to authorization will not be accepted. For international customers where applicable, customers must ship any returns to us freight and duty prepaid. Return freight charges for internationsl shippments will be the responsibility of the customer.
Defective new equipment may be returned for warrantyrepair/exchange to us within (5) days of the shipment receipt date. After five (5) days, returns will be handled by direct contact and in accordance with the warranty terms of the item's manufacturer. Items that have malfunctioned due to mishandling, electrical overload, etc., will be subject to repair charge.
Non defective new equipment will be authorized for return within five (5) days of the shipment receipt date if the equipment is still in new, re-sellable condition with the original manual(s), accessories, packing material and carton. We reserve the right to reject returnsin which there is no original packaging, missing accessories, damage or visible signs of usage of the item. A restocking fee of up to 25% of purchase price may apply. Special orders and dangerous goods are non-returnable.
(Do not write anytingon the manufacturer's original package or use as a shipping carton. Include all accessories, manuals and warranties.)
Please, include a copy of the packing list or invoice with a reason for the return. Your return authorization number is valid for thirty (30) days.
We can ship to both US and Canada. Note that there are restrictions on some products, and some products cannot be shipped to international destinations.
When you place an order, we will charge a flat rate shipping for your items.
Please also note that the shipping rates for many items we sell are weight-based. The weight of any such item can be found on its detail page. To reflect the policies of the shipping companies we use, all weights will be rounded up to the next full pound.
Not Applicable
| Condition: | NA |
Defective new equipment may be returned for warrantyrepair/exchange to us within (5) days of the shipment receipt date. After five (5) days, returns will be handled by direct contact and in accordance with the warranty terms of the item's manufacturer. Items that have malfunctioned due to mishandling, electrical overload, etc., will be subject to repair charge.
Non defective new equipment will be authorized for return within five (5) days of the shipment receipt date if the equipment is still in new, re-sellable condition with the original manual(s), accessories, packing material and carton. We reserve the right to reject returnsin which there is no original packaging, missing accessories, damage or visible signs of usage of the item. A restocking fee of up to 25% of purchase price may apply. Special orders and dangerous goods are non-returnable.
(Do not write anytingon the manufacturer's original package or use as a shipping carton. Include all accessories, manuals and warranties.)
Please, include a copy of the packing list or invoice with a reason for the return. Your return authorization number is valid for thirty (30) days.
