Canadian Dollars
Guaranteed Fitment
Always the correct part
have questions?
Always the correct part
We know our products
Fast & Reliable
Replacing the BMM2000ESD, the Megger MIT415/2 Insulation Tester gives greater application range and greater functionality with simplified operation.
The Megger MIT415 insulation and continuity tester is designed for electrical testing by utilities, industrial, commercial and domestic electricians. The wide range of test voltages makes the MIT415 series ideal for the engineer or technician involved with combined applications of both communications circuits and power circuits such as would be found in elevator service/repair and routine maintenance. The low test voltage insulation ranges also makes the MIT415 ideal for ESD testing.
| *All quoted accuracies are at +20° C. | |
| Insulation Nominal test voltages | 250 V, 500 V, 1000 V |
| Insulation resistance range | 20 G? |
| Range Full Scale Accuracy | 1000 volts ±3% ±2 digits ±0.2% per G? 500 volts ±3% ±2 digits ±0.4% per G? 250 volts ±3% ±2 digits ±0.8% per G? |
| Analog range | 1 G? full scale |
| Short Circuit Current | 2 mA +0% -50% |
| Terminal voltage | -0% +20% ±1 V |
| Test Current on load | 1 mA at min. pass value of insulation specified in BS7671, HD384and IEC364, 2 mA max. |
| EN61557 Operating range | 0.10 M½ to 1.00 G? |
| Leakage Current | 10% ±3 digits |
| Voltage display | 3% ±3 digits ±0.5% of rated voltage |
| Polarization Index (PI) | 10 min/1 minute ratio |
| Dielectric Absorption Ratio (DAR) | 60 sec/30 sec ratio |
| Notes | (1) All ranges measure from 0.00 M½ upwards. (2) Above specifications only apply when high quality silicone leadsare being used. |
| Continuity | |
| Measurement | 0.01 ½ to 99.9 ½ (0 to 100 ½ on analog scale) |
| Accuracy | ±3% ±2 digits (0 to 100 ?) |
| Open circuit voltage | 5 V ±1 V |
| Test current | 200 mA (0 mA +20 mA) (0.01 ½ to 9.99 ?) 20mA (±1 mA ) (10.0 ½ to 99.9 ?) |
| Zero offset at probe tips | 0.10? typical |
| Lead resistance zeroing | Up to 9.00 ? |
| Buzzer | Variable limit 1?, 2?, 5?,10?, 20? |
| Resistance | |
| Measurement | 0.01 k? to 1000 k? (0 to 1 M? on analog scale) |
| Accuracy | ±3% ±2 digits Open circuit voltage 5 V ±1 V Short circuit current 20 µA ± 5 µA |
| Voltage range | 0 to 600 V d.c. ±2% ±2 digits 10 mV to 600 V TRMS sinusoidal (40 to 400 Hz) ±2% ±2 digits 0 to 1000 V on Analog scale Unspecified input level 0 - 10 mV (40 to 400 Hz) For non-sinusoidal waveforms additional specification apply: ±3% ±2 digits 101 mV to 600 V TRMS and ±8% ±2 digits 10 mV to 100 mV TRMS |
| Default Voltmeter | Operates at >25 V a.c. or d.c. on any range except OFF |
| Frequency | 40 - 450 Hz (40 Hz - 99.9 Hz) ±0.5% ±1 digit (100 Hz to450 Hz) |
| Result storage | |
| Capacity | >1000 test results |
| Download | Bluetooth wireless |
| Bluetooth Class | Class II |
| Range | up to 10 m |
| Power | |
| Power Supply | 5 x 1.5 V cells type IEC LR6 (AA, MN1500, HP7, AM3 R6HP) Alkaline NiMH rechargeable cells may be used. Battery life: 2200 insulation tests with duty cycle of 5 sec ON /55 sec OFF @ 1000 V into 1 M? |
| Dimensions | |
| Instrument | 220 x 92 x 50 mm (8.66 in. x 3.63 in. x 1.97 in.) |
| Instrument and case | 456 x 178 x 89 mm (18 in. x 7 in. x 3.5 in.) |
| Weight | |
| Instrument only | 590 gms (20.73 oz.), 775 gms (27.22 oz.) with boot |
| Instrument and case | 1.75kg (3.86 lb) |
| Fuse | Use only a 500 mA (FF) 1000 V 32 x 6 mm ceramic fuse of highbreaking capacity HBC 50 kA minimum. Glass fuses MUST NOT be fitted. |
| Safety Protection | The instruments meet EN 61010-1 (1995) to 600 V phase to earth, Category IV. Refer to safety warnings supplied. |
| E.M.C. | In accordance with IEC 61326 including amendment No.1 |
| Temperature effects | |
| Temperature coefficient | <0.1&Omega per °C up to 1 G&Omega |
| Environmental | |
| Operating range | -10 to +55° C |
| Operating humidity | 90% RH at 40° C max. |
| Storage temperature range | -25 to +70° C |
| Calibration Temperature | +20° C |
| Maximum altitude | 2000 m |
| Dust and water protection | IP54 Protected against dust and splashing water |
| *All quoted accuracies are at +20° C. | |
| Insulation Nominal test voltages | 250 V, 500 V, 1000 V |
| Insulation resistance range | 20 G? |
| Range Full Scale Accuracy | 1000 volts ±3% ±2 digits ±0.2% per G? 500 volts ±3% ±2 digits ±0.4% per G? 250 volts ±3% ±2 digits ±0.8% per G? |
| Analog range | 1 G? full scale |
| Short Circuit Current | 2 mA +0% -50% |
| Terminal voltage | -0% +20% ±1 V |
| Test Current on load | 1 mA at min. pass value of insulation specified in BS7671, HD384and IEC364, 2 mA max. |
| EN61557 Operating range | 0.10 M½ to 1.00 G? |
| Leakage Current | 10% ±3 digits |
| Voltage display | 3% ±3 digits ±0.5% of rated voltage |
| Polarization Index (PI) | 10 min/1 minute ratio |
| Dielectric Absorption Ratio (DAR) | 60 sec/30 sec ratio |
| Notes | (1) All ranges measure from 0.00 M½ upwards. (2) Above specifications only apply when high quality silicone leadsare being used. |
| Continuity | |
| Measurement | 0.01 ½ to 99.9 ½ (0 to 100 ½ on analog scale) |
| Accuracy | ±3% ±2 digits (0 to 100 ?) |
| Open circuit voltage | 5 V ±1 V |
| Test current | 200 mA (0 mA +20 mA) (0.01 ½ to 9.99 ?) 20mA (±1 mA ) (10.0 ½ to 99.9 ?) |
| Zero offset at probe tips | 0.10? typical |
| Lead resistance zeroing | Up to 9.00 ? |
| Buzzer | Variable limit 1?, 2?, 5?,10?, 20? |
| Resistance | |
| Measurement | 0.01 k? to 1000 k? (0 to 1 M? on analog scale) |
| Accuracy | ±3% ±2 digits Open circuit voltage 5 V ±1 V Short circuit current 20 µA ± 5 µA |
| Voltage range | 0 to 600 V d.c. ±2% ±2 digits 10 mV to 600 V TRMS sinusoidal (40 to 400 Hz) ±2% ±2 digits 0 to 1000 V on Analog scale Unspecified input level 0 - 10 mV (40 to 400 Hz) For non-sinusoidal waveforms additional specification apply: ±3% ±2 digits 101 mV to 600 V TRMS and ±8% ±2 digits 10 mV to 100 mV TRMS |
| Default Voltmeter | Operates at >25 V a.c. or d.c. on any range except OFF |
| Frequency | 40 - 450 Hz (40 Hz - 99.9 Hz) ±0.5% ±1 digit (100 Hz to450 Hz) |
| Result storage | |
| Capacity | >1000 test results |
| Download | Bluetooth wireless |
| Bluetooth Class | Class II |
| Range | up to 10 m |
| Power | |
| Power Supply | 5 x 1.5 V cells type IEC LR6 (AA, MN1500, HP7, AM3 R6HP) Alkaline NiMH rechargeable cells may be used. Battery life: 2200 insulation tests with duty cycle of 5 sec ON /55 sec OFF @ 1000 V into 1 M? |
| Dimensions | |
| Instrument | 220 x 92 x 50 mm (8.66 in. x 3.63 in. x 1.97 in.) |
| Instrument and case | 456 x 178 x 89 mm (18 in. x 7 in. x 3.5 in.) |
| Weight | |
| Instrument only | 590 gms (20.73 oz.), 775 gms (27.22 oz.) with boot |
| Instrument and case | 1.75kg (3.86 lb) |
| Fuse | Use only a 500 mA (FF) 1000 V 32 x 6 mm ceramic fuse of highbreaking capacity HBC 50 kA minimum. Glass fuses MUST NOT be fitted. |
| Safety Protection | The instruments meet EN 61010-1 (1995) to 600 V phase to earth, Category IV. Refer to safety warnings supplied. |
| E.M.C. | In accordance with IEC 61326 including amendment No.1 |
| Temperature effects | |
| Temperature coefficient | <0.1&Omega per °C up to 1 G&Omega |
| Environmental | |
| Operating range | -10 to +55° C |
| Operating humidity | 90% RH at 40° C max. |
| Storage temperature range | -25 to +70° C |
| Calibration Temperature | +20° C |
| Maximum altitude | 2000 m |
| Dust and water protection | IP54 Protected against dust and splashing water |
| *All quoted accuracies are at +20° C. | |
| Insulation Nominal test voltages | 250 V, 500 V, 1000 V |
| Insulation resistance range | 20 G? |
| Range Full Scale Accuracy | 1000 volts ±3% ±2 digits ±0.2% per G? 500 volts ±3% ±2 digits ±0.4% per G? 250 volts ±3% ±2 digits ±0.8% per G? |
| Analog range | 1 G? full scale |
| Short Circuit Current | 2 mA +0% -50% |
| Terminal voltage | -0% +20% ±1 V |
| Test Current on load | 1 mA at min. pass value of insulation specified in BS7671, HD384and IEC364, 2 mA max. |
| EN61557 Operating range | 0.10 M½ to 1.00 G? |
| Leakage Current | 10% ±3 digits |
| Voltage display | 3% ±3 digits ±0.5% of rated voltage |
| Polarization Index (PI) | 10 min/1 minute ratio |
| Dielectric Absorption Ratio (DAR) | 60 sec/30 sec ratio |
| Notes | (1) All ranges measure from 0.00 M½ upwards. (2) Above specifications only apply when high quality silicone leadsare being used. |
| Continuity | |
| Measurement | 0.01 ½ to 99.9 ½ (0 to 100 ½ on analog scale) |
| Accuracy | ±3% ±2 digits (0 to 100 ?) |
| Open circuit voltage | 5 V ±1 V |
| Test current | 200 mA (0 mA +20 mA) (0.01 ½ to 9.99 ?) 20mA (±1 mA ) (10.0 ½ to 99.9 ?) |
| Zero offset at probe tips | 0.10? typical |
| Lead resistance zeroing | Up to 9.00 ? |
| Buzzer | Variable limit 1?, 2?, 5?,10?, 20? |
| Resistance | |
| Measurement | 0.01 k? to 1000 k? (0 to 1 M? on analog scale) |
| Accuracy | ±3% ±2 digits Open circuit voltage 5 V ±1 V Short circuit current 20 µA ± 5 µA |
| Voltage range | 0 to 600 V d.c. ±2% ±2 digits 10 mV to 600 V TRMS sinusoidal (40 to 400 Hz) ±2% ±2 digits 0 to 1000 V on Analog scale Unspecified input level 0 - 10 mV (40 to 400 Hz) For non-sinusoidal waveforms additional specification apply: ±3% ±2 digits 101 mV to 600 V TRMS and ±8% ±2 digits 10 mV to 100 mV TRMS |
| Default Voltmeter | Operates at >25 V a.c. or d.c. on any range except OFF |
| Frequency | 40 - 450 Hz (40 Hz - 99.9 Hz) ±0.5% ±1 digit (100 Hz to450 Hz) |
| Result storage | |
| Capacity | >1000 test results |
| Download | Bluetooth wireless |
| Bluetooth Class | Class II |
| Range | up to 10 m |
| Power | |
| Power Supply | 5 x 1.5 V cells type IEC LR6 (AA, MN1500, HP7, AM3 R6HP) Alkaline NiMH rechargeable cells may be used. Battery life: 2200 insulation tests with duty cycle of 5 sec ON /55 sec OFF @ 1000 V into 1 M? |
| Dimensions | |
| Instrument | 220 x 92 x 50 mm (8.66 in. x 3.63 in. x 1.97 in.) |
| Instrument and case | 456 x 178 x 89 mm (18 in. x 7 in. x 3.5 in.) |
| Weight | |
| Instrument only | 590 gms (20.73 oz.), 775 gms (27.22 oz.) with boot |
| Instrument and case | 1.75kg (3.86 lb) |
| Fuse | Use only a 500 mA (FF) 1000 V 32 x 6 mm ceramic fuse of highbreaking capacity HBC 50 kA minimum. Glass fuses MUST NOT be fitted. |
| Safety Protection | The instruments meet EN 61010-1 (1995) to 600 V phase to earth, Category IV. Refer to safety warnings supplied. |
| E.M.C. | In accordance with IEC 61326 including amendment No.1 |
| Temperature effects | |
| Temperature coefficient | <0.1&Omega per °C up to 1 G&Omega |
| Environmental | |
| Operating range | -10 to +55° C |
| Operating humidity | 90% RH at 40° C max. |
| Storage temperature range | -25 to +70° C |
| Calibration Temperature | +20° C |
| Maximum altitude | 2000 m |
| Dust and water protection | IP54 Protected against dust and splashing water |
All returns must be authorized. Items returned prior to authorization will not be accepted. For international customers where applicable, customers must ship any returns to us freight and duty prepaid. Return freight charges for internationsl shippments will be the responsibility of the customer.
Defective new equipment may be returned for warrantyrepair/exchange to us within (5) days of the shipment receipt date. After five (5) days, returns will be handled by direct contact and in accordance with the warranty terms of the item's manufacturer. Items that have malfunctioned due to mishandling, electrical overload, etc., will be subject to repair charge.
Non defective new equipment will be authorized for return within five (5) days of the shipment receipt date if the equipment is still in new, re-sellable condition with the original manual(s), accessories, packing material and carton. We reserve the right to reject returnsin which there is no original packaging, missing accessories, damage or visible signs of usage of the item. A restocking fee of up to 25% of purchase price may apply. Special orders and dangerous goods are non-returnable.
(Do not write anytingon the manufacturer's original package or use as a shipping carton. Include all accessories, manuals and warranties.)
Please, include a copy of the packing list or invoice with a reason for the return. Your return authorization number is valid for thirty (30) days.
We can ship to both US and Canada. Note that there are restrictions on some products, and some products cannot be shipped to international destinations.
When you place an order, we will charge a flat rate shipping for your items.
Please also note that the shipping rates for many items we sell are weight-based. The weight of any such item can be found on its detail page. To reflect the policies of the shipping companies we use, all weights will be rounded up to the next full pound.
Not Applicable
| Condition: | NA |
Defective new equipment may be returned for warrantyrepair/exchange to us within (5) days of the shipment receipt date. After five (5) days, returns will be handled by direct contact and in accordance with the warranty terms of the item's manufacturer. Items that have malfunctioned due to mishandling, electrical overload, etc., will be subject to repair charge.
Non defective new equipment will be authorized for return within five (5) days of the shipment receipt date if the equipment is still in new, re-sellable condition with the original manual(s), accessories, packing material and carton. We reserve the right to reject returnsin which there is no original packaging, missing accessories, damage or visible signs of usage of the item. A restocking fee of up to 25% of purchase price may apply. Special orders and dangerous goods are non-returnable.
(Do not write anytingon the manufacturer's original package or use as a shipping carton. Include all accessories, manuals and warranties.)
Please, include a copy of the packing list or invoice with a reason for the return. Your return authorization number is valid for thirty (30) days.
